30×30 Dört Yönlü Bağlantı Sacı
30×30 Dört Yönlü Bağlantı Sacı, sigma profil birleşimlerinde dıştan bağlantı oluşturmak için değerlendirilir. Profil kesiti, bağlantı yönü ve delik yerleşimi doğru montaj için birlikte kontrol edilir. İleri Mühendislik, seçiminizi ürünün teknik seçenekleri ve kullanılacağı yapının koşullarıyla birlikte ele alır.
30×30 Dört Yönlü Bağlantı Sacı — teknik bilgiler
| Catalog Code | The IM-BS-3030-4Y |
| Product Measurement | 30 × 30 |
The task of the connection
The connection hair is assessed to create an external combination between the profile surfaces and provide connectivity points in the chosen directions. The two, three or four-way definition describes the form of the placement of the slope; it does not give the load capacity alone. The profile cut, the location of the holes and the slums to be used in the connection must be matched together. It is also important in the choice that the surface to be assembled is accessible.
Control of the hole and channel compatibility
The size of the crane to be used with the hole diameter on the sac is checked along with the shell layout in the profile channel. The external size may be different between the hole intervals of the two hole that appear the same. The product size, the direction number and the necessary link set must be clearly indicated in the order. The measures shown in the technical table with letters A, B or similar are assessed along with the relevant product draw; it is not accepted that the same letter in the different product tells the same direction.
Surface, contact and assembly access
The presence of another apparatus or panel on the surface where the profile of the connector is sitting can affect the installation. The head of the connector should be left to access for pressing and subsequent maintenance. The thickness of the connector, the surface condition and the use environment are assessed along with the project. In the combinations to be used in an open or wet environment, it is not enough to look only to the profile material; the characteristics of the connector parts are also addressed.
Parts that complete the combination
The profile that appears in the assembly with the stick itself can be separate pensels, the stick and the cave. It reduces the likelihood of the material lacking to explain whether these parts are included in the offer list. The number of the stick and the connection unit to be used in a corner is determined by the movement and load conditions of the structure. The assembly example in the picture does not mean the calculated load capacity of the whole structure.
When preparing a list of measurements
The indication of which surface or edge measurements are taken prevents the mix of similar parts. Cutting length, external measurement, channel openness and connection distance are different information. The unit used in the drawing must be the same in all lines. If the new one is to be taken instead of the existing piece, not only the total length, but also the details on the link side. Sharing product groups and parts in a regular list makes the range of the offer more clear.
Identify the variant correctly.
If there are more than one measurement or connection options within the product family, specify the line to be ordered. Similar names may be prepared for different channels, metric teeth or connection surface. The options in the technical table are not considered as parts that can be used in place each other. The photo and size of the profile section in the product to be added to a existing structure can also be added to the offer request.
Projects and Proposals
The list you will share with Advanced Engineering should include the product name, catalog code, size and piece. Listing the connectors of the same structure together reduces the likelihood of missing material. If you need a specific size, surface, processing or different settings, write it also. Photos help to understand the assembly; the measurable drawing allows the accurate assessment of the connectors. The supply scope is clarified in the supply phase.
Check before installation
The name and size of the delivered product must be compared to the prepared material list. Connector surfaces and the position of the piece in the project are checked. It should not be assumed that other products in the assembly samples are included in this pen. Profile, cottage, cottage or panel may also be required. The load and movement conditions in the application are not determined about the conformity of the whole structure without the knowledge of the load and movement conditions in the application.
Frequently Asked Questions
What information do you need when choosing this product?
The profile or assembly surface to be used in addition to the product name and size should be shared, the necessary pieces and working conditions. The variant table of products clearly indicates which option is required. If adaptation to a existing system is made, the measurable drawing or sample assessment will be made easier.
Are all the pieces included in the order?
In the assembly images, the profile, the link element or the assistant parts can be displayed together. The delivery range of this pen is described during the offer. It is recommended that you specify the shell, the cottage, the panel and other parts you need separately in your list.
How to check the conformity with the existing piece?
In addition to the outer appearance, the measurements of the channel, hole, tooth and assembly surface are compared. Combination of the product code alone may not be sufficient. The measurement, photo and if necessary the relevant variants are assessed through the sample.
Important products and offers
Sigma profile and linking elements catalogue You can check out other groups. Connecting Boxes and Plakats You can compare the options in the same group from the section. with your size and list of items Ask for advanced engineering .
Examples of Application Gallery
Uygulama örnekleri
30x30 Dört Yönlü Bağlantı Sacı için bu ürüne özel hazırlanmış montaj ve kullanım örneklerini inceleyebilirsiniz.
Uygulama örnekleri seçim ve yerleşim fikri sunar. Kesit, bağlantı düzeni ve yük koşulları projeye göre değerlendirilir.