PVC banded carriers

PVC Bands Conveyor Visual Gallery

PVC band carriers and uses

PVC band carriers are used to advance boxes, packages, plastic pieces and so on a continuous transport surface. Band carriers are assessed in applications where the product base is small or the gap between the rolls can be affected. Parts feed to the assembly station, the collection of products out of the packaging machine and the creation of regular flow between the two work points are among the main uses. Advanced Engineering deals with the measurements, weight and the work order of the product to carry the carriers' installation.

The suitability of a system is not determined only by the length of the carrier. The number of products that will be found at the same time on the line, the number of products that will not accumulate on the band and the number of pieces that will be transferred per hour should be assessed together. The need for a small-based heavy piece with a light but broad-based box is different from the band and support. The sample product or the image of the existing line reduces uncertainty in the supply phase.

Band width and carrier measurements

The width of the available band is determined according to the direction in the course of the product transportation. The width of the product is added to the area covered by the side guides and the necessary work space. The width of the band is not the same measure with the width of the shell from the outside to the outside; the measure in order should be clearly indicated which measure is intended. The length of the line, the heights of entrance and output and the maintenance area around the machine are shown together in the placement drawing.

The band speed should be selected in accordance with the production amount. The speed upgrading does not always provide more efficient transportation; the products left irregularly at the entrance may accumulate at the output or lose balance. The next machine's receipt speed and the distance to be left between the products are important. The speed settings must be implemented in applications that assess the motor and driver's conformity and the appropriate control arrangement is determined.

PVC band, tambour and support surface

The band thickness, surface fabric and sub layer structure are selected according to the application. The minimum thumb diameter, working temperature and drawing conditions permitted by the band manufacturer are taken into account in the design. It is not enough to choose the band with only color or thickness information. If oil, chemical, hot product or sharp edge parts are, they should be ⁇ in the offer phase.

The swelling on the sliding surface reflects the total load and length of the carrier in the need for driving. The parallelness of the thumbs, the accuracy of the shade and the appropriate back setting are controlled together for the correct progress of the band. Trying to solve the band escape only by sliding more can carry unnecessary loads to beds and band. The access area left for the band exchange is also part of the design.

Placing on the shade, feet and production line

Aluminium profile, painted steel or stainless steel options are assessed according to the working environment. Aluminium profile structure provides flexibility in the positioning of elements such as sensors and side guides. Cleaning requirement is also important in high applications for connection details and accessible surfaces as material. The use of stainless steel alone does not indicate that the whole system is in accordance with a specific hygiene standard.

The footplaces are arranged according to the ground and the connectivity points of the machines around which the carrier will work. The operator's access to the product, the cleaning area and the transparency required to change the band are considered in advance. The direction of transportation, the access to maintenance and the possibilities of collision with the equipment around the motor are assessed together when the location is selected.

Transportation and product transitions

PVC band carriers can also be used in curved lines in the appropriate products in addition to straight transport. The appropriate curved line depends on the product base, band surface, weight center and output behavior. It is not correct to give a single curved limit applicable to each product. If there is a possibility of back curved or rotation, the palet band, side support or a different conveyor geometry will be assessed.

The gap in the entrance and output may be critical for small products. The difference in the diameter of the thumb and the coat between the two machines may cause the product to be attached or changed direction during the passage. The transfer hair or other transition solution is determined according to the product geometry. The need for transportation between different levels Type L carriers and Type Z carriers can be studied.

Motor selection and maintenance

Motor power is calculated taking into account the total moving load, speed, drilling, curvation and working time. It is not correct to accept a single motor power in accordance with all sizes and capacities. If the frequency stand-up, product accumulation or controlled power by the sensor is also assessed the working scenario. Access to moving parts, storage and stop arrangement should also be addressed along with the way of use.

In the periodic control, the band edges, the additional place, the tambour surfaces and beds are reviewed by unusual sound or heating. The outer parts entering the band may increase the stretching. The cleaning method should be compatible with the band material; the energy of the equipment should be safe cut before maintenance. The making of back and trace settings according to the manufacturer's instructions reduces the possibility of early stretching.

The price of the PVC band carrier

For the offer, the bandwidth, the carrier length, the entrance-out height, the product’s en-boy-height measurements and the one-part weight should be shared. The number of products to be simultaneously on the line, the desired speed and the daily working time should also be indicated. The range of needs such as the six-material, side guide, adjusted foot, sensor and speed control affect. If the existing machine is connected, it makes it easier to evaluate a measurable crockey or technical image.

Frequently Asked Questions

Is each PVC band suitable for food transportation? No. In the application that requires direct food contact, the suitability documents of the band and the conditions of use of the entire system should be assessed. The band color should not be based only on food contact.

Can different products be transported in the same carrier? If the size and weight range of the products are determined from the beginning, a common structure can be assessed. The need for transport of the weaker product with the passage of the smallest product should be checked together.

Can it be added later or later? Input-output coats, product flow, available area and control connections may be assessed if appropriate. Other types of carriers can be examined or You can share your size. .

The existing product information

The product	PVC banded carriers
The basic function	PVC band surface transfer of boxes, packages and pieces
Area of Application	Flat or appropriate curved production and packaging lines
Information needed in the election	Band width, line length, product weight
Technical control point	The product’s holding on the band and entrance-out passage

Product images