Injection Machine Conveyor
Injection Machine Conveyor Visual Gallery
Injection machine carriers carry out plastic parts from the model to the collection area by taking the plastic parts from the machine under or from the robot's leaving point. The release of the piece and the release of the piece by the robot requires different input arrangements. Advanced Engineering assesses the carriers according to the machine's discharge, the contact temperature of the product and the production circuit. The main choice of the surface of the piece during transportation and the proper delivery of the subsequent processing are the topics.
Installation for injection machine carriers
The available height, width and entrance distance under the machine should be measured. The machine feet, connector tubes or cover can limit the installation of the carrier. The band width should meet the real area where parts may fall. Choosing only according to the output point of a single pattern, different pattern can create insufficient collection area in production. The pattern parts of the pattern to be used are therefore assessed together.
If the carrier needs to be removed during the shape change and machine maintenance, the movement and fixing arrangement should be considered. The work position in wheel use should be securely fixed. The direction of the carrier approach to the machine, the route of the electric connections and the location plan of the area where the operator will change the cash. The maintenance corridors are not confined and the contact with the moving machine parts is checked.
The way the piece falls or leaves with a robot
The drop-down height, the weight and shape of the piece influence this behavior. The geometry that the product will reach the band without a collision should be selected if the collection shell or side barrier is needed. The spaces that thin and small pieces can enter are ⁇ studied. The shell is very narrow, it can cause the pieces to accumulate up to a row or the flow to be cut off.
The drop point in the robot application may be more controlled; but the robots' holding movement and the carrier's working moment must be matched. If the band is asked to stop or progress a certain distance when the part is left, this scenario is clearly defined. If more than one piece is left in a circle, the settings and the gap between them also affect the speed choice with the bandwidth.
Choose hot products
The material name of the piece out of the injection is not enough for the band selection alone. The temperature, the time of contact and the surface sensitivity of the piece is to be known. The temperature in the form may not be the same as the contact temperature on the band. The limit of use of the selected band and if there is, the palette, bordure or connector elements are compared to the actual working conditions.
Some newly produced parts may be more sensitive to shape change or surface trace formation. The quality of the products that come up, get a blow or wait for a long time in the same area can be affected. In this case, the range of parts, the transport time and, if necessary, the need for cooling are assessed together. The use of the carrier alone does not guarantee that the desired output temperature will be provided; the process must also be addressed.
Time of circulation and speed of transportation
The machine's rotation time, the number of parts out in each circle and the targeted range of parts are used in the selection of the transport speed. The low speed of the speed may lead to the accumulation of parts in the same area. The very high speed may lead to uncontrollable fall in the output or the inefficient use of the settlement area. The need for speed settlement should be planned along with the engine and control order.
When the machine stops, the carrier continues to work, immediately stops or stops after a certain period of time are different working forms. Communication with the robot, if the information of cash supply and piece detection is needed, the signals are included in the project scope. After the energy cessation, the rework conditions must also be defined. Thus the carrier has a clear movement order that supports the production circulation.
Type L, Type Z and Type L
If the output and collection area are similar to the height, the flat transport can be assessed. If the piece needs to be transferred to a higher box or warehouse, the L or Z type settlement is addressed. The product's sliding behavior, band palettes and side barriers are selected together for the sliding transport. If the upper horizontal delivery distance is needed, the Z type settlement can be studied according to the settlement needs.
Information for the price of the injection carrier
The offer requires the machine's six-discovery, bandwidth, transport length, entrance and output coats. The product size, weight, contact temperature, circular time and leaving height should be shared. The robot connection, collection armor, barriers, six-materia and automation cover changes the price. The machine and leaving area's measurable photos make it easier to prepare the proper settlement.
Frequently Asked Questions
Does the same transmitter alert to each injection machine? The machine's six-discovery, the piece-leaving area and maintenance access may vary. The settlement measurements must be checked according to the machine.
Can the product and the road be transported at the same time? The portability depends on the geometry of the piece. If separate collection is required, the separation arrangement of the road is also designed.
Can the carrier work according to the robot circuit? The appropriate control and communication arrangements can be assessed.The necessary order of movement and signals must be identified before order.
The existing product information
| The product | Injection Machine Conveyor |
| The basic function | Transmission of plastic parts from the pattern or the robot |
| Area of Application | Injection machine and robot side |
| Information needed in the election | Product temperature, leaving height, turn time |
| Technical control point | The suitability of the band for hot products should also be assessed |
Ask about this product or application
Product images
