Miles support and connective beds
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Check out the product families for Mil Supports and Connecting Beds, published measurement tables and resource technical images.
Key information in the selection of Mil Support and Connecting Bed
Mil supports and connective beds are the assembly parts used in the fixation of the cylindrical guide miles to the machine body. This page presents the SK and SHF families with their technical drawings. The support body is not an element that replaces the moving roll; its task is to identify the location and connection of the miles. The mile diameter and the assembly layout are assessed together for the right choice.
The base connection and body geometry in SK and SHF forms may be different. The cave centers, the center height of the mile and the milin depletion area are controlled by the source drawing. A support part is not accepted to fit with the existing body because it is only the hole that is suitable. The moving carrier's transit area should not also conflict with support.
A mile supported from two ends is important and the position of the load. The installation of the support points, the mile work length and mutual parallelity influence the guiding behavior. If the support body is connected by force to a curve ground, the mile axis can change. The conformity of the body surfaces and connective holes should be reviewed before installation.
Share the nominal diameter of the mile for the offer, the support unit and the existing assembly image. In the drawing, if the size of the opened holes or special connection is needed, specify the size of the hole. In the renewal, the base hole range and the center height are measured. If the support unit is increased, the impact on the moving rolling position and assembly tolerance will also be assessed. The right piece selection is made along with the entire connection order of the axis.
How to use technical tables?
The separate subpages of the products contain models and measurements published in the source. By clicking on a product card you can examine the images, technical drawings and tables on the separate page of that family. In different families the same letter can define a different size; therefore the symbols in the table must be read along with their own drawings. The fields left empty in the source have not been completed, a measure that is not in the drawings has not been re-produced. If the unit information is not clear, it must be verified by the manufacturer's drawings.
The tables are for technical comparison; it is not an instant stock or delivery time statement. the connection arrangement and working conditions of the products that appear in the same nominal dimension may be different. It is not necessary to make a piece change through a single number or a photo similarity only. The application requirements are compared with the full model definition. If a difference is seen in the source data, the relevant line is also checked before ordering.
Measurement and offer information
When you request the offer, share the full code of the product, the details of the item and the photo of the existing piece. Add a measurable drawing if you need a specific processing, different materials or a specific delivery range. It should be clearly stated whether a product is required as a set or as a single component. If more than one piece changes in the same machine, the connected surfaces and matching parts are assessed together.
Before installation, the connective surfaces, the working direction and the maintenance access are reviewed. The cause of the failure in the old piece may not solve the problem of the new product, the problem of the installation, the balance or the pollution without understanding. The manufacturer's installation, lubrication and use instructions are based on the selected product. The general selection description here does not replace the technical documentation of the full model. The measurement verification and application assessment ensure the proposal is openly prepared.
Interested Products Groups
To check the machine's guidelines and drive parts together Linear rail and cars , Mills and Summons and The machine spare parts You can switch between. The product selection is done taking into account the entire installation of the machine, because the tasks of the connected parts are separate. You can request evaluation by sharing your technical picture with Advanced Engineering.
clarification of order
The display of an accessory with the main product does not mean that it is inside each package. Combination components, such as connector boards, intermittent parts, rollers or engines should be specified separately on the request. When the product is delivered, the measurement draw is compared to the definition of the piece; a difference seen before the assembly is transmitted to the technical assessment. Thus, the assembly repetitions may occur due to the missing component or the wrong assembly are reduced.
Frequently Asked Questions
Is only a photo enough for Mil Support and Connecting Bed?
Photography is useful to recognize the family; for the exact choice, it requires model code, connection measurements and working conditions. The images taken from different aspects of the current piece are assessed along with the measurement technical drawing.
Are all the products on the table ready stock?
This section shows the technical product scope. Current stock, delivery time, special processing and item information are verified when the offer is prepared. Listing a technical line does not mean that a particular piece will be delivered immediately.