Servo Motor and drivers
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Check out product families for Servo Motor and Drivers, published measurement tables and resource technical images.
Servo Motor and Drivers Selection
Servo engines and drivers are the driven components selected together in the axes that require controlled position, speed or moment. This page contains product drawings and published technical tables of the servo engines and drivers family in the source. The nominal power of the engine does not define the entire movement profile alone. The load scale, speed time and mechanical transfer arrangement are also assessed during the selection.
The compatibility of the driver and the engine is not only set by the similarity of power values. the encoder type, power, control interface and manufacturer match must be verified. if the engine and driver labels are being photographed together in a existing machine. the signal or communication form used by the control system is also indicated. the support of a protocol not included in the technical document is unpredictable.
Brake and freezing arrangements, the freezing or horizontal working conditions and mechanical settings are studied together. If the engine brake is, the task and working conditions must be understood according to the manufacturer's document. In the caplin and reducer connections, the mile, flange and detection measures are checked. The settlement of the Servo system does not eliminate the mechanical equation problem on its own.
Share the moving mass, the strok or turn range for the offer, the turn time and the current transfer rate. If the reuse of existing cables and connectors is planned, this information is added to the request. The cable length and the installation environment are also assessed according to the selected system. Prepared automation panels are not added in this range; here is a technical assessment for the engine and driver product family.
How to use technical tables?
The separate subpages of the products contain models and measurements published in the source. By clicking on a product card you can examine the images, technical drawings and tables on the separate page of that family. In different families the same letter can define a different size; therefore the symbols in the table must be read along with their own drawings. The fields left empty in the source have not been completed, a measure that is not in the drawings has not been re-produced. If the unit information is not clear, it must be verified by the manufacturer's drawings.
The tables are for technical comparison; it is not an instant stock or delivery time statement. the connection arrangement and working conditions of the products that appear in the same nominal dimension may be different. It is not necessary to make a piece change through a single number or a photo similarity only. The application requirements are compared with the full model definition. If a difference is seen in the source data, the relevant line is also checked before ordering.
Measurement and offer information
When you request the offer, share the full code of the product, the details of the item and the photo of the existing piece. Add a measurable drawing if you need a specific processing, different materials or a specific delivery range. It should be clearly stated whether a product is required as a set or as a single component. If more than one piece changes in the same machine, the connected surfaces and matching parts are assessed together.
Before installation, the connective surfaces, the working direction and the maintenance access are reviewed. The cause of the failure in the old piece may not solve the problem of the new product, the problem of the installation, the balance or the pollution without understanding. The manufacturer's installation, lubrication and use instructions are based on the selected product. The general selection description here does not replace the technical documentation of the full model. The measurement verification and application assessment ensure the proposal is openly prepared.
Interested Products Groups
To check the machine's guidelines and drive parts together Linear rail and cars , Mills and Summons and The machine spare parts You can switch between. The product selection is done taking into account the entire installation of the machine, because the tasks of the connected parts are separate. You can request evaluation by sharing your technical picture with Advanced Engineering.
clarification of order
The display of an accessory with the main product does not mean that it is inside each package. Combination components, such as connector boards, intermittent parts, rollers or engines should be specified separately on the request. When the product is delivered, the measurement draw is compared to the definition of the piece; a difference seen before the assembly is transmitted to the technical assessment. Thus, the assembly repetitions may occur due to the missing component or the wrong assembly are reduced.
Frequently Asked Questions
Is the Servo Motor and Drivers only enough?
Photography is useful to recognize the family; for the exact choice, it requires model code, connection measurements and working conditions. The images taken from different aspects of the current piece are assessed along with the measurement technical drawing.
Are all the products on the table ready stock?
This section shows the technical product scope. Current stock, delivery time, special processing and item information are verified when the offer is prepared. Listing a technical line does not mean that a particular piece will be delivered immediately.