Miles of beds
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Check out the product families for the Wide Miles Bed, published scale tables and resource technical images.
Basic information in the choice of mil beds
The sliding mile beds are used to support the millin ends as the drive axis requires. On this page, the BK, BF, FK and FF families can be studied with separate technical titles. The task of the fixed and support side is not the same. When a team is selected, the millin processed ends, the bed interior size and the connection surface of the machine are assessed together.
The fixed side solutions of BK and FK, while the BF and FF are considered as the support side family. The body form and connection arrangement vary according to the family. The bed number alone does not have to be the same number as the nominal diameter of the slide mill. The matching is done through the mill processed bed neck and shoulder measurements; not only the exterior diameter of the slide is determined.
The lock layout of the fixed side is important in terms of the preservation of the millin axle position. On the support side, the installation must be done in accordance with the designed work layout. The lock shell, the pul, the caplin and the bed shoulder are studied together in the same end draw. A type of roll or the pre-load value not specified in the source is not attributed to the whole family as a common feature.
If a renewal is done in a existing machine, share the photo and dimensions of both ends. The body's basin holes, the center height and connection direction must be determined. The caplin side is marked which end is. The mil is also studied during the bed change, the dissolving or equalizing error. The seating of a bed body in the cottage holes does not prove the suitability of the end processing and axis geometry alone.
How to use technical tables?
The separate subpages of the products contain models and measurements published in the source. By clicking on a product card you can examine the images, technical drawings and tables on the separate page of that family. In different families the same letter can define a different size; therefore the symbols in the table must be read along with their own drawings. The fields left empty in the source have not been completed, a measure that is not in the drawings has not been re-produced. If the unit information is not clear, it must be verified by the manufacturer's drawings.
The tables are for technical comparison; it is not an instant stock or delivery time statement. the connection arrangement and working conditions of the products that appear in the same nominal dimension may be different. It is not necessary to make a piece change through a single number or a photo similarity only. The application requirements are compared with the full model definition. If a difference is seen in the source data, the relevant line is also checked before ordering.
Measurement and offer information
When you request the offer, share the full code of the product, the details of the item and the photo of the existing piece. Add a measurable drawing if you need a specific processing, different materials or a specific delivery range. It should be clearly stated whether a product is required as a set or as a single component. If more than one piece changes in the same machine, the connected surfaces and matching parts are assessed together.
Before installation, the connective surfaces, the working direction and the maintenance access are reviewed. The cause of the failure in the old piece may not solve the problem of the new product, the problem of the installation, the balance or the pollution without understanding. The manufacturer's installation, lubrication and use instructions are based on the selected product. The general selection description here does not replace the technical documentation of the full model. The measurement verification and application assessment ensure the proposal is openly prepared.
Interested Products Groups
To check the machine's guidelines and drive parts together Linear rail and cars , Mills and Summons and The machine spare parts You can switch between. The product selection is done taking into account the entire installation of the machine, because the tasks of the connected parts are separate. You can request evaluation by sharing your technical picture with Advanced Engineering.
clarification of order
The display of an accessory with the main product does not mean that it is inside each package. Combination components, such as connector boards, intermittent parts, rollers or engines should be specified separately on the request. When the product is delivered, the measurement draw is compared to the definition of the piece; a difference seen before the assembly is transmitted to the technical assessment. Thus, the assembly repetitions may occur due to the missing component or the wrong assembly are reduced.
Frequently Asked Questions
Is only a photo enough for a mil bed?
Photography is useful to recognize the family; for the exact choice, it requires model code, connection measurements and working conditions. The images taken from different aspects of the current piece are assessed along with the measurement technical drawing.
Are all the products on the table ready stock?
This section shows the technical product scope. Current stock, delivery time, special processing and item information are verified when the offer is prepared. Listing a technical line does not mean that a particular piece will be delivered immediately.