Type Z carriers
Type Z Conveyor Visual Gallery
Z type carriers consist of the lower-orphal product receipt section, the curved elevation section and the upper-orphal delivery section. It is used to transfer products from the machine output to a higher warehouse, box or other production station. Advanced Engineering solves the entrance and output conditions in the same location by separating the dimensions of the three parts. The upper-orphal section creates a area that will allow the product to be delivered in a controlled manner after curved.
Measurement of three parts for Type Z carriers
The length of the lower horizontal part is chosen according to where and how the product comes. If there are more than one output under the machine, the collection area should meet them. The seam part is determined by assessing the required amount of elevation and the available ground area together. The length of the upper horizontal part is dependent on the distance the output needs to lay on a cage or to approach the next machine.
The total height does not describe the settlement alone. The entrance coat, the output coat, the net band width and the area covered by the three parts in the horizon should be shown in the drawing. The feet, the engine, the reserves and the band back layout are also included in the external measurements. The area assigned for the opening of the machine cover next to the carrier, the exchange of the box and the access to maintenance should be protected.
Band palettes and transport divisions
The range and height of these profiles called palettes are selected according to the product dimensions. The amount of product falling into a division depends not only on the size of a single piece, but also on the feeding frequency. The fullness of division and the possibility of shifting for parts gathering from the machine should be assessed.
Side barriers or borders can limit the output of small pieces out of the band. The gap between moving palettes, barriers and fixed six parts is especially important for thin products. The product must advance without tired into these spaces. The band material and accessories are selected in accordance with the temperature, oil and contact characteristics of the product. The palette and band structure are not determined only in terms of the angle of the curvature.
The lower and upper transition areas
The Z type carrier has two different direction shift areas. The product in the bottom part goes from the horizon to the curve, the top part goes back to the bed from the curved movement. The band support and the direction geometry must be checked at both passes. The passage of long products, the movement of round products or the accumulation of small pieces between the palettes can cause different design needs.
The real piece behavior is studied in order to ensure the product does not return and move to the output at the top passage. The band turn diameter and the position of the palettes must correspond to the limits of the band system used at the passage. The assessment by the product sample can only reveal problems of unnoticed fixing or direction change on the drawing. If different products are to be moved, the smallest and largest pieces are handled together.
Food and output control
The top horizontal part should be determined at the end of which point the product will be left. The mouth of the cage, the output end and the fall path of the product must be matched. The fall distance in sensitive parts may affect surface damage. The cage or cage will change as the emission conditions will change, and if the need for the detection of availability or controlled stop is included in the project scope.
The amount of power is assessed along with the transmitter speed. With a constantly working even product flow, the machine circle is not the same as the flow that gives a mass product at the end. The speed setting, the machine ready signal and the position of the product should be explained where the product will wait on the band. This information also affects the choice of the engine and control mode along with mechanical design.
Şase ve bakım düzeni
The length distance of the upper horizontal part affects the support order. Foot positions and ground connections are assessed to ensure the carrier's balanced work. Tracking band, back, palet connections and transition points are left with maintenance access. The recovery of product remains at the bottom turn or on the barrier edge should be regularly checked. Cleaning and piece exchange must be done in safe stop conditions.
Information for the price of the Z type carrier
The measurements of the lower horizontal, curved and top horizontal parts for the offer; the entrance-out coats and bandwidth are required. The product size, weight, temperature, hour amount and feed form should be shared. The band palettes, barriers, shase material, warehouse connection and automation coverage change the price. The measurement crocky that shows the positions of warehouse with the existing machine is useful for proper settlement.
Frequently Asked Questions
When is the type Z carrier preferred? The product is assessed when it is necessary to move along a horizontal distance after upgrade or to deliver to a specific point.
Can the upper horizontal section be extended later? The band length, support structure, stimulation and balance should be re-controled. It may not be enough to add to the shade alone.
Can the palette range be the same in all products? The size of the product and the amount that comes to each division may vary if the appropriate range. The product varieties must be specified before ordering.
The existing product information
| The product | Type Z carriers |
| The basic function | Change the level with lower horizontal, curved and upper horizontal parts |
| Area of Application | Injection and feed out |
| Information needed in the election | The length of three parts, total height, product size |
| Technical control point | The palet and barriers geometry should be checked at the band turn points. |
Ask about this product or application
Product images
