The Reducers
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Check out product families for Reducers, published measurement tables and source technical images.
Basic information in the selection of reducers
The start of a reducer choice is the determination of the speed and moment required in the output as the motor power. The machine's work circle, the number of output and the load change are not determined by the body number without the knowledge. In this section, the infinite teeth, planet and cycloid families; also the connection flags and bricks are presented in separate product titles. The table of each family is assessed in its own geometry and work characteristics.
The planet reducer controls the flange size of the engine, the mile diameter and the form of connection. The source has different body options of the ZD and Sesame families. The angle gap, the bond ratio and the connection measurements are not the values used to replace each other. In particular, in the servo axis, the mechanical adaptation to the engine does not indicate that the desired positioning behavior is obtained alone. The movement profile is also considered in the choice.
The fact that the planet's order is provided with the infinite dental order does not mean that it will show the same application behavior. The direction of work, the installation location, the environment and the load character should be shared during the selection. The radal and axonal effects from the output mile are also studied. The seating of a driver group to the existing connection is not sufficient without checking the conformity of the load conditions.
In the renewal, the photo of the old label, the engine information, the connection surfaces and the image of the output side must be sent together. The shell and detection layout on the mile are also measured. The brake, special output or flange details not included in a short code are explained on the offer. The connection brakes and flags can also be considered as separate parts from the main reducer; the required unit and delivery range must be indicated.
How to use technical tables?
The separate subpages of the products contain models and measurements published in the source. By clicking on a product card you can examine the images, technical drawings and tables on the separate page of that family. In different families the same letter can define a different size; therefore the symbols in the table must be read along with their own drawings. The fields left empty in the source have not been completed, a measure that is not in the drawings has not been re-produced. If the unit information is not clear, it must be verified by the manufacturer's drawings.
The tables are for technical comparison; it is not an instant stock or delivery time statement. the connection arrangement and working conditions of the products that appear in the same nominal dimension may be different. It is not necessary to make a piece change through a single number or a photo similarity only. The application requirements are compared with the full model definition. If a difference is seen in the source data, the relevant line is also checked before ordering.
Measurement and offer information
When you request the offer, share the full code of the product, the details of the item and the photo of the existing piece. Add a measurable drawing if you need a specific processing, different materials or a specific delivery range. It should be clearly stated whether a product is required as a set or as a single component. If more than one piece changes in the same machine, the connected surfaces and matching parts are assessed together.
Before installation, the connective surfaces, the working direction and the maintenance access are reviewed. The cause of the failure in the old piece may not solve the problem of the new product, the problem of the installation, the balance or the pollution without understanding. The manufacturer's installation, lubrication and use instructions are based on the selected product. The general selection description here does not replace the technical documentation of the full model. The measurement verification and application assessment ensure the proposal is openly prepared.
Interested Products Groups
To check the machine's guidelines and drive parts together Linear rail and cars , Mills and Summons and The machine spare parts You can switch between. The product selection is done taking into account the entire installation of the machine, because the tasks of the connected parts are separate. You can request evaluation by sharing your technical picture with Advanced Engineering.
clarification of order
The display of an accessory with the main product does not mean that it is inside each package. Combination components, such as connector boards, intermittent parts, rollers or engines should be specified separately on the request. When the product is delivered, the measurement draw is compared to the definition of the piece; a difference seen before the assembly is transmitted to the technical assessment. Thus, the assembly repetitions may occur due to the missing component or the wrong assembly are reduced.
Frequently Asked Questions
Is only a picture enough for the reducers?
Photography is useful to recognize the family; for the exact choice, it requires model code, connection measurements and working conditions. The images taken from different aspects of the current piece are assessed along with the measurement technical drawing.
Are all the products on the table ready stock?
This section shows the technical product scope. Current stock, delivery time, special processing and item information are verified when the offer is prepared. Listing a technical line does not mean that a particular piece will be delivered immediately.