Spindle Motor and Drivers
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Check out the product families for Spindle Motor and Drivers, published measurement tables and resource technical images.
Basic information in selecting Spindle Motor and Drivers
Spindle engines and drivers are assessed according to the rotative drive requirements in the processing applications. This page contains the appearance and technical tables of the spindle product family in the source. It should not be selected in the same way as a general electric engine. Working circuit, holding layout, cooling form and mechanical connectivity surface are studied together in the choice.
The equipment holders, the method of processing and material information are included in the product assessment. Nominal power alone does not mean the same processing behavior in the entire rotation range. The driver's power and conformity with the engine must be verified. A automatic equipment change or the specific sensor feature not specified in the technical source is unpredictable in terms of the product name.
When renewed with a existing spindle, the engine label, body diameter, connection layout and driver model are shared together. If there are cooling connections, the directions and existing facilities are photographed. The same appearance of the connector or cable layout does not prove electrical compatibility. The existing layout of the machine should be compared to the manufacturer connection scheme.
The required turn range, the working time and the processing task for the offer are specified. The end and body measurements that sit on the machine are added to the drawing. If the change is due to vibration or heating complaint, the reason must also be investigated. This page does not provide a ready automation panel; the spindle engine and the appropriate driver focus on the technical assessment of the product family.
How to use technical tables?
The separate subpages of the products contain models and measurements published in the source. By clicking on a product card you can examine the images, technical drawings and tables on the separate page of that family. In different families the same letter can define a different size; therefore the symbols in the table must be read along with their own drawings. The fields left empty in the source have not been completed, a measure that is not in the drawings has not been re-produced. If the unit information is not clear, it must be verified by the manufacturer's drawings.
The tables are for technical comparison; it is not an instant stock or delivery time statement. the connection arrangement and working conditions of the products that appear in the same nominal dimension may be different. It is not necessary to make a piece change through a single number or a photo similarity only. The application requirements are compared with the full model definition. If a difference is seen in the source data, the relevant line is also checked before ordering.
Measurement and offer information
When you request the offer, share the full code of the product, the details of the item and the photo of the existing piece. Add a measurable drawing if you need a specific processing, different materials or a specific delivery range. It should be clearly stated whether a product is required as a set or as a single component. If more than one piece changes in the same machine, the connected surfaces and matching parts are assessed together.
Before installation, the connective surfaces, the working direction and the maintenance access are reviewed. The cause of the failure in the old piece may not solve the problem of the new product, the problem of the installation, the balance or the pollution without understanding. The manufacturer's installation, lubrication and use instructions are based on the selected product. The general selection description here does not replace the technical documentation of the full model. The measurement verification and application assessment ensure the proposal is openly prepared.
Interested Products Groups
To check the machine's guidelines and drive parts together Linear rail and cars , Mills and Summons and The machine spare parts You can switch between. The product selection is done taking into account the entire installation of the machine, because the tasks of the connected parts are separate. You can request evaluation by sharing your technical picture with Advanced Engineering.
clarification of order
The display of an accessory with the main product does not mean that it is inside each package. Combination components, such as connector boards, intermittent parts, rollers or engines should be specified separately on the request. When the product is delivered, the measurement draw is compared to the definition of the piece; a difference seen before the assembly is transmitted to the technical assessment. Thus, the assembly repetitions may occur due to the missing component or the wrong assembly are reduced.
Frequently Asked Questions
Is Spindle Motor and Drivers Only Photo Ready?
Photography is useful to recognize the family; for the exact choice, it requires model code, connection measurements and working conditions. The images taken from different aspects of the current piece are assessed along with the measurement technical drawing.
Are all the products on the table ready stock?
This section shows the technical product scope. Current stock, delivery time, special processing and item information are verified when the offer is prepared. Listing a technical line does not mean that a particular piece will be delivered immediately.