The Acordion Conveys
The visual gallery of the accordiation carriers
The accordion carriers create a transport route in different lengths thanks to the open and closed stack shelves. These systems used in charging, discharge and temporary product transfer can be parked in a smaller area when the work is completed. Advanced Engineering, accordion carriers in the choice of open and closed heights, product base, work height and ground state assess together. Adjustable structure requires a clear definition of the conditions of use in the design.
Open and closed size for the accortion carriers
The longest distance required during the work is the area that the carrier will accommodate when it is gathered. Only the indication of the open neck does not guarantee that there is a suitable parking area in front of the door or in the warehouse. The closed size, the total outer width and the area covered by the wheels are included in the settlement plan. If the carrier is used in different doors, the narrow passes on the transport route should also be checked.
As the armor body is opened, the distance between the transporting elements may vary. Therefore, the smallest box must not only be closed, but also receive sufficient support in the most open position permitted. Opening the system outside the appropriate working limits to increase the line length may affect the product passage and the body stability. Opening limits should be clearly monitored during use.
Roll or wheel transportation surface
The base structure of the product determines the choice of the transport element. The boxes with the feet on the base with flat and sufficiently rough collars can act differently on the same surface. Small boxes, soft packaging or irregular bases can be placed in support intervals. The example of the smallest and weakest product to be transported or the base photo should be shared in the offer stage.
With the progress of the product alone, the movement of more than one product back to back also creates different conditions. It is important how the load is distributed throughout the carrier, how many arms will even be found at the same time and how the operator leaves the product. Transport capacity is not expressed only by the total line length. The opening amount, the foot position and the contact form of the load should be assessed together.
The movement and movement of the product
The flexible body helps to fit the route within the appropriate structure and use limits. But each product cannot pass every turn half-drive. The corners of the long arms can cover a wider area than the flat line during the turn. The settlement difference between the transport elements on the inside and the external sides can affect the product's balance. Therefore, the planned return should be controlled by the actual product sizes.
If necessary, side guides or elements that limit the output of the product are treated in conformity with their adjustable structure. The entrance and output ends of the carrier must be kept in a position that is suitable for the fixed machine or charging point. During the turn, the wheels should not move in the unwanted direction and the feet should be balanced supported.
Work height, curvature and ground
Adjustable height can make it easier to adapt to different charging points. However, the curved product formed between entrance and output changes the movement speed. In motorless use, light and heavy collars may not progress at the same speed in the same curved line. The stop at the end of the line, the delivery to the operator and the conditions of the contact of the products are assessed together.
The curvature, edge or disorder on the ground affects the load sharing of the wheels and the stability of the carrier. It is important that the area to be used is straight and the wheels are properly fixed. The passes near the charging door, the coat differences and the movement area between the vehicle and the building floor should also be studied. The suitability to carry the carrier during the charging of the product depends on the system's defined conditions of use.
Care and use of the body
The roof connections, the roofs, the wheels and the height settlement mechanisms are regularly controlled. The roof connections, the curved transport elements or the hard-to-roof wheels may negatively affect the movement. During opening and closing, the hands should not enter the roof areas. The appropriate holding points and enough free space in the surrounding area should be provided for use. Cleaning and maintenance are done after the load is lifted and the system is brought to a safe position.
Information for the price of the transfer
The desired open-cover size, net transport width, height range and product weight are required for the offer. The product base, planned turns, ground condition and use frequency should also be shared. The choice of wheels and transport surface, side guides, end connections and if there is, the price of the drive needs will affect. The photo of entrance and output points with the area's measurable crocissus will help to prepare the solution in the right range.
Frequently Asked Questions
Can the accordion carrier be used at any length? The system must remain within the designed opening range throughout the work. Product support and body balance should be checked at the most open location.
Are the products going on by themselves? The movement in the motorless system depends on the curve, the product base and the resistance of the transport elements. The same curve may not be enough for each product.
Can the carrier be easily collected after use? The structure of the roof is intended for this; but appropriate parking space and safe opening-stop conditions must be provided. Transport and clamping process must be done in accordance with the system's instructions for use.
The existing product information
| The product | The Acordion Conveys |
| The basic function | Transition and transfer of the sixth-course |
| Area of Application | Loading, discharge and variable settlement areas |
| Information needed in the election | Open-Closed Size, Work Height, Product Base |
| Technical control point | As the extension amount changes, the distance between the transporting elements may change. |
Ask about this product or application
Product images
