Linear Rulman and Bed Car
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Check out the product families for Linear Rulman and Bed Car, published measurement tables and source technical images.
Basic information in the choice of linear rollers and bed cars
Linear rollers are parts with different body and contact arrangements used for linear guidance on the cylindrical miller. The linear rollers are included in the separate product titles with the sliding families presented under the title of the teflon in this section. The assembly tasks of the locked, open, semi-long, flange and bed body options are not the same. The choice is made together with the mile diameter and the carrier body.
Open-type products are considered to be used on the appropriate under-backed mile. It is unpredictable that a closed type roll will pass in the same way in an axis with a support geometry. Connection holes and shoulder surfaces are controlled in square or round flags. The short and long type difference does not only affect the appearance, but also the area divided in the assembly.
The source contains different families under the headlines LME, LMEK, LMEF, SCE, SBR and TBR. The short code is similar, does not mean that the outer diameter and total neck are equal. The working millin surface character, the rolling form and the environmental conditions are studied together. The lubrication, drilling and maintenance approach in the sliding and balled arrangements is determined according to the product's own instructions.
The surface, the direction of movement and the points where the load is applied to the new design should be shared. The full code of the old piece is photographed in the renewal with readable; the mile diameter, the external body diameter, the flange size and size are recorded. The cause of the climbing within the body is not only to change the roll without research, the problem of equalization is not eliminated. Technical tables help to compare different families; the exact matching is done with the drawing.
How to use technical tables?
The separate subpages of the products contain models and measurements published in the source. By clicking on a product card you can examine the images, technical drawings and tables on the separate page of that family. In different families the same letter can define a different size; therefore the symbols in the table must be read along with their own drawings. The fields left empty in the source have not been completed, a measure that is not in the drawings has not been re-produced. If the unit information is not clear, it must be verified by the manufacturer's drawings.
The tables are for technical comparison; it is not an instant stock or delivery time statement. the connection arrangement and working conditions of the products that appear in the same nominal dimension may be different. It is not necessary to make a piece change through a single number or a photo similarity only. The application requirements are compared with the full model definition. If a difference is seen in the source data, the relevant line is also checked before ordering.
Measurement and offer information
When you request the offer, share the full code of the product, the details of the item and the photo of the existing piece. Add a measurable drawing if you need a specific processing, different materials or a specific delivery range. It should be clearly stated whether a product is required as a set or as a single component. If more than one piece changes in the same machine, the connected surfaces and matching parts are assessed together.
Before installation, the connective surfaces, the working direction and the maintenance access are reviewed. The cause of the failure in the old piece may not solve the problem of the new product, the problem of the installation, the balance or the pollution without understanding. The manufacturer's installation, lubrication and use instructions are based on the selected product. The general selection description here does not replace the technical documentation of the full model. The measurement verification and application assessment ensure the proposal is openly prepared.
Interested Products Groups
To check the machine's guidelines and drive parts together Linear rail and cars , Mills and Summons and The machine spare parts You can switch between. The product selection is done taking into account the entire installation of the machine, because the tasks of the connected parts are separate. You can request evaluation by sharing your technical picture with Advanced Engineering.
clarification of order
The display of an accessory with the main product does not mean that it is inside each package. Combination components, such as connector boards, intermittent parts, rollers or engines should be specified separately on the request. When the product is delivered, the measurement draw is compared to the definition of the piece; a difference seen before the assembly is transmitted to the technical assessment. Thus, the assembly repetitions may occur due to the missing component or the wrong assembly are reduced.
Frequently Asked Questions
Is only photo enough for linear rollers and bed-to-bed cars?
Photography is useful to recognize the family; for the exact choice, it requires model code, connection measurements and working conditions. The images taken from different aspects of the current piece are assessed along with the measurement technical drawing.
Are all the products on the table ready stock?
This section shows the technical product scope. Current stock, delivery time, special processing and item information are verified when the offer is prepared. Listing a technical line does not mean that a particular piece will be delivered immediately.