Step Motor and Drivers
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Check out product families for Step Motor and Drivers, published measurement tables and resource technical images.
Step Motor and Drivers Selection
Step engine and drivers are evaluated together in the machine arrangements that require step motion. This page contains the family of step engine and step engine drivers in the source in separate technical titles. The body size of the engine alone does not determine the moment it will provide at every speed. The driver, the feed and the movement profile to be used should be studied together.
The engine's phase structure, current information and connection definition are necessary for the driver's choice. The actual mechanical accuracy of the machine with the micro step setting is not the same concept. When a control setting is increased, it is impossible to assume that all the system's position errors will automatically decrease. The features of the wire mile, caplin or thread transfer are also included in the movement account.
The label, cable output and connection surface are photographed during the current engine renewal. The mile diameter and flange hole centers are measured. Different sizes, current or connection arrangements may be found in the same body class. The power and control entries on the driver are verified according to their own manufacturer document. A protection or communication feature not presented in the drawing is not generally assigned to the product family.
Share the desired speed, drive, load and rotation frequency during the offer. If the system is expected to open or reboot work, note also. The step loss caused by mechanical lock or excess load may not be solved by only renewing the engine in the same size. This section addresses the engine and driver components instead of the ready panel; the relevant source tables must be read in this scope.
How to use technical tables?
The separate subpages of the products contain models and measurements published in the source. By clicking on a product card you can examine the images, technical drawings and tables on the separate page of that family. In different families the same letter can define a different size; therefore the symbols in the table must be read along with their own drawings. The fields left empty in the source have not been completed, a measure that is not in the drawings has not been re-produced. If the unit information is not clear, it must be verified by the manufacturer's drawings.
The tables are for technical comparison; it is not an instant stock or delivery time statement. the connection arrangement and working conditions of the products that appear in the same nominal dimension may be different. It is not necessary to make a piece change through a single number or a photo similarity only. The application requirements are compared with the full model definition. If a difference is seen in the source data, the relevant line is also checked before ordering.
Measurement and offer information
When you request the offer, share the full code of the product, the details of the item and the photo of the existing piece. Add a measurable drawing if you need a specific processing, different materials or a specific delivery range. It should be clearly stated whether a product is required as a set or as a single component. If more than one piece changes in the same machine, the connected surfaces and matching parts are assessed together.
Before installation, the connective surfaces, the working direction and the maintenance access are reviewed. The cause of the failure in the old piece may not solve the problem of the new product, the problem of the installation, the balance or the pollution without understanding. The manufacturer's installation, lubrication and use instructions are based on the selected product. The general selection description here does not replace the technical documentation of the full model. The measurement verification and application assessment ensure the proposal is openly prepared.
Interested Products Groups
To check the machine's guidelines and drive parts together Linear rail and cars , Mills and Summons and The machine spare parts You can switch between. The product selection is done taking into account the entire installation of the machine, because the tasks of the connected parts are separate. You can request evaluation by sharing your technical picture with Advanced Engineering.
clarification of order
The display of an accessory with the main product does not mean that it is inside each package. Combination components, such as connector boards, intermittent parts, rollers or engines should be specified separately on the request. When the product is delivered, the measurement draw is compared to the definition of the piece; a difference seen before the assembly is transmitted to the technical assessment. Thus, the assembly repetitions may occur due to the missing component or the wrong assembly are reduced.
Frequently Asked Questions
Is the photo only enough for the Step Motor and Drivers?
Photography is useful to recognize the family; for the exact choice, it requires model code, connection measurements and working conditions. The images taken from different aspects of the current piece are assessed along with the measurement technical drawing.
Are all the products on the table ready stock?
This section shows the technical product scope. Current stock, delivery time, special processing and item information are verified when the offer is prepared. Listing a technical line does not mean that a particular piece will be delivered immediately.