Linear Activator
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Linear Activators — product options, technical tables and application-based selection information.
Linear actors are the driving elements that turn the rotation movement of the electric motor into linear progress within the body. On this page, the models D 60, D 11, DF, D 21, D 5 and D 10 are presented along with the published product images. The strength, strok, speed and connection form required when selecting the model must be addressed in the same assessment. Only the appearance of the product or the engine power is not sufficient for the whole selection.
Altı modelin kaynak bilgileri
6000 and 4000 N for D 60 and DF; 1000 and 1500 N for D 11; 1500 and 2000 N for D 21 are published. the D 5 model has the definitions of 100–800 N, the D 10 model has the definitions of 8000 and 10000 N. These are the power information in the source; which variants are also to be determined with which speed or strok. The 12 and 24 VDC options listed for all models are transmitted to the table with the same range.
For example, the writing of two strength values on the side does not mean that one necessarily push the other is the pull capacity. Full model and variant certificate for technical acceptance is required. Unconfirmed numbers for strok, speed, work circle and closed size have not been produced.
DF and protection
The DF family has the water and dust protection option defined by the source as IP66. The protection column of other models is left empty because there is no clear information in the source. The protection definition in a family should not be transmitted to all the actors. The connection cable, connector, the assembly direction and the environment to be used are assessed by the certificate of the selected product.
Distance and connection
The required strok is the distance between the two positions of the moving element. The length between the connector's fully closed connector centers is a different measure. The area covered by the body and the angle of the connector's mafs are also controlled in the design. The strok alone does not indicate whether a activator will mechanically fit the machine.
If a cover or lifting hand is to be moved, the hand length of the activator can vary throughout the movement. The mass of the moving piece is not directly equal to the required linear force. The drawing of the connector points and the starting end positions of the movement should be shared. If the activator is expected to work under a side load or a tendance that pushes the body, this should also be studied.
Food and control arrangements
12 VDC and 24 VDC are different power options. The current system must verify the power voltage and control order while renewed. The mention of a model in the source list with both voltage does not indicate that a single device works with the same features in both voltage. The label and connection information of the variant to be purchased is based on the control unit's current and connection requirements are assessed together with the product.
This section focuses on the product families of the operator. No ready automation panel or speed adjustment panel has been added. The information of the supply and control required to fit the customer's current control mode is shared in the supply phase. The electric connection must be prepared according to the manufacturer scheme of the chosen variant; the general product photo should not be used instead of a connection scheme.
Information and maintenance
The desired stroke, time of movement, strength, the number of circuits in the day and the environmental conditions are indicated. The label of the existing activator, the closed and open position measurements and the photos of the connection pime diamonds are useful. The dismantling plan is also assessed how the moving piece will be kept while the drawing plan is made. The maintenance and work circuit is determined according to the own instructions of the selected product.
Interested movements
If you need a guided axis on the body Mills of Motion Modules and Linear rail and cars A open wire mile axis with an electric piston is not the same product; the load guidance and connection installation are assessed separately according to the project.
Frequently Asked Questions
Can I choose the speed and speed from the table?
The source does not publish them on the model basis, so this page does not provide a precise strok or speed list. Your needs and the full variant are also verified.
Does each model have the same protection for the outside environment?
No. Here only the definition of IP66 specified in the source for DF is shown; the protection of other models must also be verified.
clarification of order
After the product selection, the unit, delivery scope and if there is a special processing need must be explained in writing. It is unpredictable that the engine, cable, connector or other component shown together in the visual is included in each package. The label and connector measures of the delivered piece are compared to the approved definition before the installation begins. If the difference is seen, the installation is not attempted to be adapted by forcing the installation; the piece information is shared for technical assessment.