Chain and Chain Teeth
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Chain and Chain Dentist — product options, technical tables and application-based selection information.
Chain and chain dentists are power transfer elements that work together in the transmission of the turn movement between two or more miles. In this section, the selected transmission chain records with the 08B and 12B single-range dentists are presented in technical tables. Knowing only the step of the existing chain is not always enough. The number of rounds, the size of the spoon and the connection order of the dentist should be checked together.
08B ve 12B dişli grupları
08B record 1/2 inches, 12B record 3/4 inches is related to the product family. The tables show the lines, the outer and section diameter and other published measurements in the forms found in the source lines. The scope here is not the entire manufacturer catalogue; it is the selected model record that can be accessed and the cells can be verified. A different number of teeth or double order of the product is also evaluated with full code when required.
Source model codes are protected for technical matching purposes. These codes are not presented as a new brand code produced by Advanced Engineering. When the number of teeth of two teeth in the same line changes, the environmental speed, the area it covers and the transfer rate can also change. Only the outlook should not be passed to a different number of teeth.
The technical table of the measurements
The Hattve, de, dp, d, D, H and h1 columns are protected by the titles published in the source. The surface of which small and large symbols describe, especially, must be verified by the original technical drawing of the relevant product. A uncertainty that may occur in the source title, not was converted into the size of a hole or stomach by commenting. When the processing picture is prepared, a precise production measure should not be accepted by the move of a letter in the table only.
Choosing the transmission chain
The chosen chain table contains the P line, the W inner width, the D square diameter, the d pim diameter and other width definitions found in the source. Millimetre measurements with the inches family are kept in separate columns. The relevant measurements and order structure for a chain's seating are studied together. A measurement made due to the extinction of the old chain may erroneously show the nominal line of the new chain.
The drainage value published in the source should not be interpreted as the permitted continuous work load. The drainage power, speed, blow and working conditions are also assessed. The maintenance and working recommendations in different manufacturers or variants of the same chain code may be different. The lubrication arrangement and environmental conditions should be examined along with the technical documentation of the selected product.
Information and repair
The parallelity of two mills and the presence of the teeth in the same working level are checked. The abdominal holes, the chassis channels and the detection order must be indicated in the drawing. The standard product's hole processing status or the special hole to be prepared is written in the offer definition. The chain tension should not be adjusted by assumpting a force value not in the source; the instructions of the application and the manufacturer are based on.
If a renewal is done in a existing carrier, share the codes of the small and large tooth, the number of chain rows and the distance between the miles centers. The cause of the climbing on the piece may not solve the problem of the new chain installation, equalization or lubrication without investigation. The protection guard is also checked in the installation that it does not collide with the new tooth installation.
Visual and Offer
The above visual is the family view of the chain transfer on your current site; the measurement of a particular model in the table is not a proof. The original source images are not shown as the official real model photo of another product for models that are not accessible to the original source images. In the offer request you can share the working conditions with the model, piece, hole and cage measurements.
For the interests of the drawing The Reducers , The cappellars and The Conveys You can check the sections. if the line is synchronized transfer is considered Triger tracks and shells It is a separate product group.
Frequently Asked Questions
Do you use a double-range tooth instead of a single-range tooth?
The order structure is matched with the chain; having the same line does not provide conformity alone.
Are all the orchestras in this picture?
No. Here are selected records that can be accessed. Other families and variants must also be verified through full code.
clarification of order
After the product selection, the unit, delivery scope and if there is a special processing need must be explained in writing. It is unpredictable that the engine, cable, connector or other component shown together in the visual is included in each package. The label and connector measures of the delivered piece are compared to the approved definition before the installation begins. If the difference is seen, the installation is not attempted to be adapted by forcing the installation; the piece information is shared for technical assessment.