The under-supported Miller
Ürün modellerini inceleyin
Ürün görseline veya adına tıklayarak ilgili serinin teknik bilgilerine ulaşın.
Check out the product families for Under-Supported Miller, published measurement tables and source technical images.
Basic information in the selection of Under-Supported Miller
The under-backed miller is the movement elements in which the silinder guide mill is combined with a carrier support throughout. This section contains connective plates and fixing rings with product families in the GCR15 and CK45. The assembly layout of the support base up to the mile diameter is also important in the choice. The piece should be assessed along with the appropriate open type roll and the body layout of the machine.
A millin supported along the length requires continuity and accuracy. The draw of the under support to a curved ground with the curves can change the guide axis. Therefore, the body surface, connectivity intervals and mutual parallelity are checked before the installation. The open part of the rolling body should be in accordance with the support geometry; the parts that appear close to each other should not be matched without the measurement comparison.
The fixing ring and the mile under support connector plate take different tasks than the main guide. The measurements of these accessories should not narrow the passage area of the working rolling body. The necessary space is left at the ends of the movement. Transfer the stroke load of the machine to a ring not designed for the stop task should not be preferred only because the installation is easy.
During the offer, the total length of the mill, the strok to be used, the size of the carrier body and the location of the load are shared. The end process or the base is shown in the picture if a special hole is needed. The selection of the materials listed in the source is also taken into account when the rolling and work circle of the existing machine is taken into account. The form of support is not removed from the product name only where a form of support is directly compatible with another brand.
How to use technical tables?
The separate subpages of the products contain models and measurements published in the source. By clicking on a product card you can examine the images, technical drawings and tables on the separate page of that family. In different families the same letter can define a different size; therefore the symbols in the table must be read along with their own drawings. The fields left empty in the source have not been completed, a measure that is not in the drawings has not been re-produced. If the unit information is not clear, it must be verified by the manufacturer's drawings.
The tables are for technical comparison; it is not an instant stock or delivery time statement. the connection arrangement and working conditions of the products that appear in the same nominal dimension may be different. It is not necessary to make a piece change through a single number or a photo similarity only. The application requirements are compared with the full model definition. If a difference is seen in the source data, the relevant line is also checked before ordering.
Measurement and offer information
When you request the offer, share the full code of the product, the details of the item and the photo of the existing piece. Add a measurable drawing if you need a specific processing, different materials or a specific delivery range. It should be clearly stated whether a product is required as a set or as a single component. If more than one piece changes in the same machine, the connected surfaces and matching parts are assessed together.
Before installation, the connective surfaces, the working direction and the maintenance access are reviewed. The cause of the failure in the old piece may not solve the problem of the new product, the problem of the installation, the balance or the pollution without understanding. The manufacturer's installation, lubrication and use instructions are based on the selected product. The general selection description here does not replace the technical documentation of the full model. The measurement verification and application assessment ensure the proposal is openly prepared.
Interested Products Groups
To check the machine's guidelines and drive parts together Linear rail and cars , Mills and Summons and The machine spare parts You can switch between. The product selection is done taking into account the entire installation of the machine, because the tasks of the connected parts are separate. You can request evaluation by sharing your technical picture with Advanced Engineering.
clarification of order
The display of an accessory with the main product does not mean that it is inside each package. Combination components, such as connector boards, intermittent parts, rollers or engines should be specified separately on the request. When the product is delivered, the measurement draw is compared to the definition of the piece; a difference seen before the assembly is transmitted to the technical assessment. Thus, the assembly repetitions may occur due to the missing component or the wrong assembly are reduced.
Frequently Asked Questions
Is only a photo enough for the under-supported Miller?
Photography is useful to recognize the family; for the exact choice, it requires model code, connection measurements and working conditions. The images taken from different aspects of the current piece are assessed along with the measurement technical drawing.
Are all the products on the table ready stock?
This section shows the technical product scope. Current stock, delivery time, special processing and item information are verified when the offer is prepared. Listing a technical line does not mean that a particular piece will be delivered immediately.