Thomson's Mil and the Smoons
The product family for Thomson Wire Mil and Smoons, size drawings and application-based selection information.
Thomson's slide mil and slides are selected by assessing the shape of the slide and the work requirements in the metric axis installation together. This page helps to identify the slide families and compare the existing piece with the technical documentation. Thomson's product images on our old site are protected, the relevant technical pages of the manufacturer catalogue are added to the review section. So the general look and the measurement table can be studied by separating each other.
The definition of FK, FH and FL
The source catalogue contains the definitions of FK and FH in the KGF-D group; the definitions of KGF-L and FL in the pre-loaded single sum group. In an old technical picture it is possible to have only a short family name. In this case, the mile diameter, progress and sum connection measures must be matched together. The hole order or sum length of the similar flanches should not be accepted the same.The manufacturer's product family may find flushed, cylindrical and dental shapes. But the local technical document on this page is limited to the selected pages from certain flushed families. The model photo for a form not found here is also evaluated through a full code or a full code. It is not correct to use a measurement in the document as a common value for all Thomson's flushed millers.
The current edge
The progress setting in the control system should also be consistent with the mechanical part. If the progress per motor turn changes, the current position commands may not give the same movement. Therefore, the advance of the old mill is determined by the catalogue or controlled measurement. Only the outer diameter is similar to the chosen part, even if it is mechanically connected, may not provide the expected movement.Access to the fixing surface and the lubrication connection of the thumb body should be considered in the early stages of the new design. The conformity of the old lubrication line to the new thumb is also verified in the parts changes in the business. The cleaning of the wire mil and axis equation are important in the preservation of proper movement. The code, drawing and movement circle you will share for Thomson will be examined together and the supply scope is clarified; a capacity not confirmed by the manufacturer documents will not be declared.
Product family and technical selection table
| The Catalog Family | Defined | Control |
|---|---|---|
| The KGF-D / FK | The only flagship | Connection and Circulation |
| KGF-D / FH | The only flagship | Full size line |
| The KGF-L / FL | One-time front charged | The front load and body measurements |
Original technical drawings and measurement tables
Technical drawings and measurements · source PDF page 15
Technical drawings and measurements · source PDF page 16
Technical drawings and measurements · source PDF page 18
Üreticinin güncel ürün bilgisi ↗
What information should you share for the offer?
Set out the total length of the mill, the work strok and the end processing measurements by separating each other. The total length can also enter bed spots, the caplin connection and the safety shell teeth. Just reporting the distance of movement is not enough to determine the full length of the piece to be prepared. Transmitting the photo of the sample in your hand along with a measurable drawing reduces the possibility of misconduct, especially when adapted to the existing machine.In addition to the mass to be moved, share the direction of movement, desired speed, drive, working frequency and environmental conditions. The axis of lifting the river is not equally assessed with a horizontal table. The mile diameter does not determine the capacity of transport alone; the free size, the layer layout, the structure of the slope and the work circle are studied together. The exact load values must only be taken from the technical documentation of the full model selected.
Things to take care of in the installation and maintenance
The fixed side bed, the support side and the body of the shell should be installed on the same axis. Trying to remove the shell error by over-tension of the connective cravings does not provide proper movement. Millin end processes are prepared according to the sizes of the bed, the lock shell and the caplin. The seating of the shell on the body with the bed shell tolerance is separately controlled; the first operation is done at low speed.The type of lubricant and the range of renewal are determined according to the manufacturer's instructions, the working environment and the actual circle. The protection blindness and appropriate scatter solution are assessed in machines with slurry, dust or liquid. The bullying shell should not be removed over a mile without the appropriate transfer apparatus. The cause of damage to the old part during renewal should also be investigated; the problem of equalization or pollution should not be assumed solved only with the installation of the new shell.
Products and technical assessment
The full axis Miles of beds to guide the burden. Linear rail and cars You can check the section if you need a ready carrier body and drive unit Mills of Motion Modules The tasks of these products are different; while turning the vibration movement to the advance, the guidelines carry the geometry of the moving element. The correct solution is determined by assessing the whole axis.Frequently Asked Questions
Is the old FK code enough to choose a new piece?
No. Nominal diameter, progress and the definition of the producer piece must be completed. The short family name is used only as the initial information.
Can the metric and inches be mixed?
The local document on this page is selected from the metric product group; similar appearances do not directly create equivalent.