Hiwin Miles and Somuns
HIWIN VIDAL MILL and SUMMERS product family, size drawings and application-based selection information.
HIWIN slides and slides can be evaluated by different forms of slides for machine axes that seek controlled linear progress. This page brings together the FSI, FSC and FSZ families; the selected manufacturer drawings and measurement tables of each family are opened with separate titles. Knowing the name of a series is the first step; the diameter, progress, precision and slides layout of the equipment to be supplied are clarified before order.
FSI, FSC and FSZ
If a change is made in a existing shell, it is useful to photograph the outer shell and the cut surfaces of the flange. The center of the connective holes should not be determined by the diameter of the mile without measuring the location of the lubricating hole and the length of the shell. The same nominal wire measurement may contain different circulation orders and shell geometries. Therefore, the following family definition is not a commitment to directly replacing a particular piece.The HIWIN source catalogue deals with stone and ovaled slurry mills in separate sections. The local document here includes the pages selected from the FSC / FSI table in the DIN section, as well as the ovaled FSZ and FSC measurements. The section covered by the document is clearly specified; the precision or size in a table is not automatically transferred to another series. The following external link can also be used for the current manufacturer information.
Plan and Axis Plan
Even if the mile body is suitable, the processed ends must be the same as the old machine. The diameter of the caplin, the bed neck, the lock female and the shoulder distance should be shown on the drawing. In the offer request, indicating which end of the engine side is, passes before a reverse end process. The expectation of emptiness in the movement in both directions of the axis should also be written.Critical turn control in a short-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track fast-track
Product family and technical selection table
| Family | Control Point | Information of order |
|---|---|---|
| FSI | The DIN measurement is checked with the table | The type, the type, the type, the type, the type, the type, the type, the type, the type, the type, the type, the type, |
| FSC | Flanch geometry and connection arrangement are verified | Difference between stone and stone |
| FSZ | Small body options are matched with the catalogue | Full code and axle emptiness |
Original technical drawings and measurement tables
Technical drawings and measurements · source PDF page 159
Technical drawings and measurements · source PDF page 160
Technical drawings and measurements · source PDF page 170
Üreticinin güncel ürün bilgisi ↗
What information should you share for the offer?
Set out the total length of the mill, the work strok and the end processing measurements by separating each other. The total length can also enter bed spots, the caplin connection and the safety shell teeth. Just reporting the distance of movement is not enough to determine the full length of the piece to be prepared. Transmitting the photo of the sample in your hand along with a measurable drawing reduces the possibility of misconduct, especially when adapted to the existing machine.In addition to the mass to be moved, share the direction of movement, desired speed, drive, working frequency and environmental conditions. The axis of lifting the river is not equally assessed with a horizontal table. The mile diameter does not determine the capacity of transport alone; the free size, the layer layout, the structure of the slope and the work circle are studied together. The exact load values must only be taken from the technical documentation of the full model selected.
Things to take care of in the installation and maintenance
The fixed side bed, the support side and the body of the shell should be installed on the same axis. Trying to remove the shell error by over-tension of the connective cravings does not provide proper movement. Millin end processes are prepared according to the sizes of the bed, the lock shell and the caplin. The seating of the shell on the body with the bed shell tolerance is separately controlled; the first operation is done at low speed.The type of lubricant and the range of renewal are determined according to the manufacturer's instructions, the working environment and the actual circle. The protection blindness and appropriate scatter solution are assessed in machines with slurry, dust or liquid. The bullying shell should not be removed over a mile without the appropriate transfer apparatus. The cause of damage to the old part during renewal should also be investigated; the problem of equalization or pollution should not be assumed solved only with the installation of the new shell.
Products and technical assessment
The full axis Miles of beds to guide the burden. Linear rail and cars You can check the section if you need a ready carrier body and drive unit Mills of Motion Modules The tasks of these products are different; while turning the vibration movement to the advance, the guidelines carry the geometry of the moving element. The correct solution is determined by assessing the whole axis.Frequently Asked Questions
Do FSI and FSC have the same connection measurements?
Not only is decided by the family name. the outer diameter, the length of the slum, the flange and hole centers in the drawing should be compared by the full model.
Does the document on the HIWIN page cover the entire catalogue?
Local document is the selected technical pages. The source section is indicated under the drawing; the current product page of the manufacturer and the full code are used for other variants.