The magnetic lock



The magnetic lock is an option that is evaluated along with the project’s measurement and installation needs in the group of locks, cuts, cuts and locks. Advanced Engineering deals with your choice along with the technical options of the product and the conditions of the structure to be used.
The magnetic lock — technical information
| Catalog Code | The IM-SA-MK |
Variation and Variation Options
| Catalog Code | The size / choice | Technical values |
| The IM-SA-MK-01 | The magnet | The product / ölçü tanımına bakınız |
Opening Panel and Access Settings
The shell, the shell and the locks make it easier to use the cover or the open panel in the profile shells. The opening direction of the door, the panel weight and user access are determined together. The lock position with the lock's location should serve the same work scenario. The choice of the lock or the holding is made according to what function is expected when the cover is closed.
The surface and connection measurements
The seating of the piece on the profile surface is controlled along with the hole range and the layout of the cottage-smoon to be used. The profile section may change the connection even if the same different panel settings. The panel remains in front or inside according to the shade, affects the opening behavior of the shade. The offer must explain the profile size, the panel thickness and the necessary assembly direction.
The area of movement and daily use
When the cover is fully opened, it should not collide with the machine, wall or other panel around it. The gap for the cluster is left where the hand can reach easily. The bully or magnetic holding may be a piece aimed at keeping the locked position; if there is a expectation of security lock, this is also defined. The staff protection function should not be accepted only through standard cover equipment.
Product change and maintenance
The relief in the shelves is monitored if there is a disorder of equalization or movement in the clock connection. When the panel weight or size is changed, the suitability of the equipment is re-evaluated. The use circle in the very often opened cover is important. If a solution can be dissolved or installed in different directions is required, it must be checked that it is in line with the technical options of the product.
When preparing a list of measurements
The indication of which surface or edge measurements are taken prevents the mix of similar parts. Cutting length, external measurement, channel openness and connection distance are different information. The unit used in the drawing must be the same in all lines. If the new one is to be taken instead of the existing piece, not only the total length, but also the details on the link side. Sharing product groups and parts in a regular list makes the range of the offer more clear.
Identify the variant correctly.
If there are more than one measurement or connection options within the product family, specify the line to be ordered. Similar names may be prepared for different channels, metric teeth or connection surface. The options in the technical table are not considered as parts that can be used in place each other. The photo and size of the profile section in the product to be added to a existing structure can also be added to the offer request.
Projects and Proposals
The list you will share with Advanced Engineering should include the product name, catalog code, size and piece. Listing the connectors of the same structure together reduces the likelihood of missing material. If you need a specific size, surface, processing or different settings, write it also. Photos help to understand the assembly; the measurable drawing allows the accurate assessment of the connectors. The supply scope is clarified in the supply phase.
Check before installation
The name and size of the delivered product must be compared to the prepared material list. Connector surfaces and the position of the piece in the project are checked. It should not be assumed that other products in the assembly samples are included in this pen. Profile, cottage, cottage or panel may also be required. The load and movement conditions in the application are not determined about the conformity of the whole structure without the knowledge of the load and movement conditions in the application.
Frequently Asked Questions
What information do you need when choosing this product?
The profile or assembly surface to be used in addition to the product name and size should be shared, the necessary pieces and working conditions. The variant table of products clearly indicates which option is required. If adaptation to a existing system is made, the measurable drawing or sample assessment will be made easier.
Are all the pieces included in the order?
In the assembly images, the profile, the link element or the assistant parts can be displayed together. The delivery range of this pen is described during the offer. It is recommended that you specify the shell, the cottage, the panel and other parts you need separately in your list.
How to check the conformity with the existing piece?
In addition to the outer appearance, the measurements of the channel, hole, tooth and assembly surface are compared. Combination of the product code alone may not be sufficient. The measurement, photo and if necessary the relevant variants are assessed through the sample.
Important products and offers
Sigma profile and linking elements catalogue You can check out other groups. Clocks, clocks and locks You can compare the options in the same group from the section. with your size and list of items Ask for advanced engineering .
Examples of Application Gallery



Uygulama örnekleri
Mıknatıslı Kilit için bu ürüne özel hazırlanmış montaj ve kullanım örneklerini inceleyebilirsiniz.
Uygulama örnekleri seçim ve yerleşim fikri sunar. Kesit, bağlantı düzeni ve yük koşulları projeye göre değerlendirilir.
