45×45 straight corner connection
45×45 Flat Count Connection is an option assessed along with the project’s measurement and installation needs in the group of count and count connections. Advanced Engineering deals with your choice along with the technical options of the product and the conditions of the structure to be used.
45×45 Flat Corner Connection — Technical information
| Catalog Code | IM-SA-DUZ-4545-K10 |
Variation and Variation Options
| Catalog Code | The size / choice | Technical values |
| IM-SA-DUZ-4545-K10 | 45×45 straight corner connection | Profile group: 45 × 45 mm · Connection type: Flat corner |
Choose the corner and internal connection
The corner connections are used to combine the profile ends or surfaces with a specific corner. The outward corner, inner edge, drawing or mafsal layout meets different assembly needs. If it is to be worked in a narrow area, the outward-tracking measurements of the connection part are important. If the visible surface needs to remain clean, corner setting or frequent discharge, they must be specified before the choice.
Not matching the profile
The conformity with the profile channel and the assembly surface is also controlled as the nominal size of the connection piece. The existence of an option for different cuts in a product family does not mean that all options will be used in place of each other. The channel sum and the metric size of the cave must be matched with the relevant variant. The assembly plan explains from which surface the product will be connected and whether the profile end needs to be processed.
Fixed angle and adjustable combination
The mafsal or apparatus that allows to change the angle with the fixed corner element is not in the same task. The corner-sized part must be determined in which position and how it will be fixed during the work. The combination that will be fixed and fixed with a combination requested to be moved is differently assessed. The moment and the openness around which the load applies to the connection are studied together.
Installation area and maintenance
When the connection element is placed, the area where the key can reach the cuts should be left. The closure of the panel, cable or other devices makes it difficult to set this area later. The condition of the connections is checked in repeated discharge and adhesion processes. When a problem of calming or alignment is seen, the profile and the conformity of the shell are also reviewed instead of just pressing the piece more.
When preparing a list of measurements
The indication of which surface or edge measurements are taken prevents the mix of similar parts. Cutting length, external measurement, channel openness and connection distance are different information. The unit used in the drawing must be the same in all lines. If the new one is to be taken instead of the existing piece, not only the total length, but also the details on the link side. Sharing product groups and parts in a regular list makes the range of the offer more clear.
Identify the variant correctly.
If there are more than one measurement or connection options within the product family, specify the line to be ordered. Similar names may be prepared for different channels, metric teeth or connection surface. The options in the technical table are not considered as parts that can be used in place each other. The photo and size of the profile section in the product to be added to a existing structure can also be added to the offer request.
Projects and Proposals
The list you will share with Advanced Engineering should include the product name, catalog code, size and piece. Listing the connectors of the same structure together reduces the likelihood of missing material. If you need a specific size, surface, processing or different settings, write it also. Photos help to understand the assembly; the measurable drawing allows the accurate assessment of the connectors. The supply scope is clarified in the supply phase.
Check before installation
The name and size of the delivered product must be compared to the prepared material list. Connector surfaces and the position of the piece in the project are checked. It should not be assumed that other products in the assembly samples are included in this pen. Profile, cottage, cottage or panel may also be required. The load and movement conditions in the application are not determined about the conformity of the whole structure without the knowledge of the load and movement conditions in the application.
Frequently Asked Questions
What information do you need when choosing this product?
The profile or assembly surface to be used in addition to the product name and size should be shared, the necessary pieces and working conditions. The variant table of products clearly indicates which option is required. If adaptation to a existing system is made, the measurable drawing or sample assessment will be made easier.
Are all the pieces included in the order?
In the assembly images, the profile, the link element or the assistant parts can be displayed together. The delivery range of this pen is described during the offer. It is recommended that you specify the shell, the cottage, the panel and other parts you need separately in your list.
How to check the conformity with the existing piece?
In addition to the outer appearance, the measurements of the channel, hole, tooth and assembly surface are compared. Combination of the product code alone may not be sufficient. The measurement, photo and if necessary the relevant variants are assessed through the sample.
Important products and offers
Sigma profile and linking elements catalogue You can check out other groups. The corner and internal connections You can compare the options in the same group from the section. with your size and list of items Ask for advanced engineering .
Examples of Application Gallery
Uygulama örnekleri
45×45 Düz Köşe Bağlantı için bu ürüne özel hazırlanmış montaj ve kullanım örneklerini inceleyebilirsiniz.
Uygulama örnekleri seçim ve yerleşim fikri sunar. Kesit, bağlantı düzeni ve yük koşulları projeye göre değerlendirilir.